Typically with nylon 6 and nylon 6,6 you can "wash" out the caprolactam with boiling water or water vapor or other polar solvents like methanol, but most of the moneymaking for polyamides are in hot melt processing, after the macromolecule has been formed and frozen solid.
source: Redditshow context
With glass you can always wipe it off and try again, too (although a solvent is probably required if you're using paint markers).
source: Redditshow context
I don't know if the acetone (as a solvent) absorbed into the plastic and affected the adhesion of the paint.
source: Redditshow context
WD40 isn't even a lubricant... its a solvent
source: Reddit
I use NAPTHA for the solvent because it flashes off quicker than mineral spirits.
source: Redditshow context
soapy water and a soft cloth will probably do it, just make sure not to use any solvents or abrasive fabrics.
source: Reddit
Tasting solvents tells you jack shit and you definitely c a n t taste -caines
source: Reddit show context
Lots of solvent and time.
source: Redditshow context
All kinds of fuel, plus paint, thinner, alcohol-based solvents/cleaners.
source: Redditshow context
Really, it's a solvent, but it doesn't attack plastic or rubber.
source: Redditshow context
Objectively, Russia is more solvent than France.
source: Redditshow context
Any economy that depends on endless population growth to stay healthy is FUBAR and not truly solvent anyway.
source: Redditshow context
I think of winterizing as a dual solvent and dewaxing being done with a single solvent; personally prefer a single solvent because I feel like it helps keep the terpenes strong because you deal with the same polarity of your solvent.
source: Redditshow context
It sounds like you use a carrier solvent though, do your ever experiment with single solvent dewaxing runs?
source: Redditshow context
8/10 runs are single solvent.
source: Redditshow context
As far as single solvent dewaxing like blasting directly into dry ice and such, no.
source: Redditshow context
I have done a few solvent less extractions though.
source: Redditshow context
The propellant and solvent cause me to hack for days.
source: Redditshow context
I'll usually get nitro solvent poured into the gas tube and let it soak in a couple minutes, then I'll spray it out with compressed air to blast anything out.
source: Redditshow context
A note to anyone attempting them, use less of your solvent - it's very tedious to evaporate liquid when you can't heat it very much for fear of the stuff you want degrading.
source: Redditshow context
Yeah, but that's compared to an internal standard (ferrocene works well for 1H NMR), not the solvent peak.
source: Reddit
Any glue left on the window can be removed with solvent.
source: Redditshow context
Keep a bit of universal solvent on you, but hide it.
source: Redditshow context
9 solvent with a bore brush and patches til the barrel is clean.
source: Redditshow context
wd-40, PB and seafoam are not lubricants, those are all solvents.
source: Redditshow context
Bubble hash needs some fairly specific micron filters to separate it out properly and you obviously know you need a solvent butane/propane/co2 etc and unless you want to be on the news you should do it outside.
source: Redditshow context
Alright I'll be the one to say it, I want to see the solvent painting.
source: Redditshow context
(Chemical methods of disabling primers like dousing them in solvents are unreliable).
source: Redditshow context
Iron needs to be in a solvent to be digested properly.
source: Redditshow context
Also good because you can change the permanent marker bits with the right solvent, so can go back and change it afterwards.
source: Redditshow context
The "solvent based acrylic paints" is a completely accurate tagline for most airbrush lacquers.
source: Redditshow context
Basically it's an acrylic pigment (the color) in "lacquer" solvents (the carrier in the jar - which is why your paint isn't powder).
source: Redditshow context
This is why acrylic paints thin so well with lacquer thinners (tested tried and true with Tamiya acrylics and Mr. Color Aqueous), but use alcohol or water based solvents to cut down on toxicity.
source: Redditshow context
Nations are corporations, all solvent governments are.
source: Redditshow context
To expand: the taste and smell differences are more likely to come from solvents or other (hopefully) harmless byproducts, than simply proportions of the compound present.
source: Redditshow context
The first part of it is that acetone is a strong organic solvent, which means if you mix it together with another organic compound like styrofoam or plastic, it can attract tiny parts of that compound to itself and pull it away, thus forming a liquid solution.
source: Redditshow context
Drying alcohol damages the skin barrier, IMO only use products with it way down the ingredients list (can be a solvent for useful plant extracts).
source: Redditshow context
Organic solvents and Meguiar's spray wax.
source: Reddit
Brake cleaner is a solvent, do not use it on paint.
source: Reddit
"organic solvents" means carbon based solvents like benzene.
source: Redditshow context
Otherwise it wouldn't make sense for something to have a bad reputation because it's made with organic solvents.
source: Redditshow context
Chemistry joke about polar/non-polar solvents
source: Reddit
Is it OK to buy salicylic acid 2% solution (solvent - alcohol) as an exfoliant from a drug store or do I need to buy a normal skincare product?
source: Redditshow context
Dual solvent dewaxing is old tech and destroys valuable terps IME.
source: Redditshow context
Or if you really want to dewax it, PM /u/slabamberson for his single solvent dewaing tech.
source: Redditshow context
So, ye sniffer of solvents, here's a breakdown of how exactly 'jewish' came to be thought of as both a race and a religion.
source: Redditshow context